|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
DATASHEET LOW SKEW 1 TO 4 CLOCK BUFFER Description The ICS524 is a low skew, single input to four output, clock buffer. Part of ICS' ClockBlocksTM family, this is our lowest skew, small clock buffer. See the ICS552-02 for a 1 to 8 low skew buffer. For more than eight outputs, see the MK74CBxxx BuffaloTM series of clock drivers. ICS makes many non-PLL and PLL based low skew output devices as well as Zero Delay Buffers to synchronize clocks. Contact us for all of your clocking needs. ICS524 Features * * * * * * * * Extremely low skew outputs (50 ps maximum) Packaged in 8-pin SOIC Available in Pb (lead) free package Low power CMOS technology Operating voltages of 2.5 V to 5 V Output Enable pin tri-states outputs 5 V tolerant input clock Industrial temperature range Block Diagram Q0 Q1 ICLK Q2 Q3 IDTTM / ICSTM LOW SKEW 1 TO 4 CLOCK BUFFER 1 ICS524 REV A 101705 ICS524 LOW SKEW 1 TO 4 CLOCK BUFFER FAN OUT BUFFER Pin Assignment ICLK Q0 Q1 NC 1 2 3 4 8 7 6 5 8-pin SOIC GND Q3 Q2 VDD Pin Descriptions Pin Pin Number Name 1 2 3 4 5 6 7 8 ICLK Q0 Q1 NC VDD Q2 Q3 GND Pin Type Input Output Output Power Output Output Power Clock input, 5V tolerant input. Clock output 0. Clock output 1. Pin Description Do not connect this pin to anything. Connect to +2.5 V, +3.3 V or +5.0 V. Clock Output 2. Clock Output 3. Connect to ground. External Components A minimum number of external components are required for proper operation. A decoupling capacitor of 0.01 F should be connected between VDD on pin 5 and GND on pin 8, as close to the device as possible. A 33 series terminating resistor may be used on each clock output if the trace is longer than 1 inch. To achieve the low output skew that the ICS524 is capable of, careful attention must be paid to board layout. Essentially, all four outputs must have identical terminations, identical loads and identical trace geometries. If they do not, the output skew will be degraded. For example, using a 30 series termination on one output (with 33 on the others) will cause at least 15 ps of skew. IDTTM / ICSTM LOW SKEW 1 TO 4 CLOCK BUFFER 2 ICS524 REV A 101705 ICS524 LOW SKEW 1 TO 4 CLOCK BUFFER FAN OUT BUFFER Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS524. These ratings, which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Supply Voltage, VDD Output Enable and All Outputs ICLK Ambient Operating Temperature Storage Temperature Junction Temperature Soldering Temperature 7V Rating -0.5 V to VDD+0.5 V -0.5 V to 5.5 V -40 to +85C -65 to +150C 125C 260C Recommended Operation Conditions Parameter Ambient Operating Temperature Power Supply Voltage (measured in respect to GND) Min. -40 +2.375 Typ. Max. +85 +5.25 Units C V DC Electrical Characteristics VDD=2.5 V 5%, Ambient temperature -40 to +85C, unless stated otherwise Parameter Operating Voltage Input High Voltage, ICLK Input Low Voltage, ICLK Output High Voltage Output Low Voltage Operating Supply Current Nominal Output Impedance Input Capacitance Short Circuit Current Symbol VDD VIH VIL VOH VOL IDD ZO CIN IOS Conditions Note 1 Note 1 IOH = -16 mA IOL = 16 mA No load, 135 MHz ICLK Min. 2.375 VDD/2+0.5 2 Typ. Max. 2.625 5.5 VDD/2-0.5 0.4 Units V V V V V mA pF mA 25 20 5 28 IDTTM / ICSTM LOW SKEW 1 TO 4 CLOCK BUFFER 3 ICS524 REV A 101705 ICS524 LOW SKEW 1 TO 4 CLOCK BUFFER FAN OUT BUFFER DC Electrical Characteristics (continued) VDD=3.3 V 5% , Ambient temperature -40 to +85C, unless stated otherwise Parameter Operating Voltage Input High Voltage, ICLK Input Low Voltage, ICLK Output High Voltage Output Low Voltage Output High Voltage (CMOS Level) Operating Supply Current Nominal Output Impedance Input Capacitance Short Circuit Current Symbol VDD VIH VIL VOH VOL VOH IDD ZO CIN IOS Conditions Note 1 Note 1 IOH = -25 mA IOL = 25 mA IOH = -12 mA No load, 135 MHz ICLK Min. 3.15 VDD/2+0.7 2.4 Typ. Max. 3.45 5.5 VDD/2-0.7 0.4 Units V V V V V V VDD-0.4 35 20 5 50 mA pF mA VDD=5 V 5% , Ambient temperature -40 to +85C, unless stated otherwise Parameter Operating Voltage Input High Voltage, ICLK Input Low Voltage, ICLK Output High Voltage Output Low Voltage Output High Voltage (CMOS Level) Operating Supply Current Nominal Output Impedance Input Capacitance Short Circuit Current Symbol VDD VIH VIL VOH VOL VOH IDD ZO CIN IOS Conditions Note 1 Note 1 IOH = -35 mA IOL = 35 mA IOH = -12 mA No load, 135 MHz ICLK Min. 4.75 VDD/2+1 2.4 Typ. Max. 5.25 5.5 VDD/2-1 0.4 Units V V V V V V VDD-0.4 45 20 5 80 mA pF mA Notes: 1. Nominal switching threshold is VDD/2 IDTTM / ICSTM LOW SKEW 1 TO 4 CLOCK BUFFER 4 ICS524 REV A 101705 ICS524 LOW SKEW 1 TO 4 CLOCK BUFFER FAN OUT BUFFER AC Electrical Characteristics VDD = 2.5 V 5%, Ambient Temperature -40 to +85C, unless stated otherwise Parameter Input Frequency Output Rise Time Output Fall Time Propagation Delay Output to Output Skew Device to Device Skew tOR tOF Note 1 Note 2 Rising edges at VDD/2 Rising edges at VDD/2 0.8 to 2.0 V, CL=15 pF 2.0 to 0.8 V, CL=15 pF 2.2 Symbol Conditions Min. 0 Typ. 1.0 1.0 3 0 Max. Units 200 1.5 1.5 5 50 500 MHz ns ns ns ps ps VDD = 3.3 V 5%, Ambient Temperature -40 to +85C, unless stated otherwise Parameter Input Frequency Output Rise Time Output Fall Time Propagation Delay Output to Output Skew Device to Device Skew tOR tOF Note 1 Note 2 Rising edges at VDD/2 Rising edges at VDD/2 0.8 to 2.0 V, CL=15 pF 2.0 to 0.8 V, CL=15 pF 2.0 Symbol Conditions Min. 0 Typ. 0.6 0.6 2.4 0 Max. Units 200 1.0 1.0 4 50 500 MHz ns ns ns ps ps VDD = 5 V 5%, Ambient Temperature -40 to +85C, unless stated otherwise Parameter Input Frequency Output Rise Time Output Fall Time Propagation Delay Output to Output Skew Device to Device Skew tOR tOF Note 1 Note 2 Rising edges at VDD/2 Rising edges at VDD/2 0.8 to 2.0 V, CL=15 pF 2.0 to 0.8 V, CL=15 pF 1.8 Symbol Conditions Min. 0 Typ. 0.3 0.3 2.5 0 Max. Units 200 0.7 0.7 4 50 500 MHz ns ns ns ps ps Notes: 1. With rail to rail input clock 2. Between any 2 outputs with equal loading. 3. Duty cycle on outputs will match incoming clock duty cycle. Consult ICS for tight duty cycle clock generators. Thermal Characteristics Parameter Thermal Resistance Junction to Ambient Symbol JA JA JA JC Conditions Still air 1 m/s air flow 3 m/s air flow Min. Typ. 150 140 120 40 Max. Units C/W C/W C/W C/W Thermal Resistance Junction to Case IDTTM / ICSTM LOW SKEW 1 TO 4 CLOCK BUFFER 5 ICS524 REV A 101705 ICS524 LOW SKEW 1 TO 4 CLOCK BUFFER FAN OUT BUFFER Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Narrow Body) Package dimensions are kept current with JEDEC Publication No. 95 Millimeters Symbol 8 Inches* Min Max Min Max A A1 B E H 1.35 0.10 0.33 0.19 4.80 3.80 5.80 0.25 0.40 0 1.75 0.25 0.51 0.25 5.00 4.00 6.20 0.50 1.27 8 .0532 .0040 .013 .0075 .1890 .1497 .2284 .010 .016 0 .0688 .0098 .020 .0098 .1968 .1574 .2440 .020 .050 8 C D E e H h L INDEX AREA 1.27 BASIC 0.050 BASIC 12 D *For reference only. Controlling dimensions in mm. A A1 h x 45 C -Ce B SEATING PLANE L .10 (.004) C Ordering Information Part / Order Number ICS524MILF ICS524MILFT Marking 524MILF 524MILF Shipping Packaging Tubes Tape and Reel Package 8-pin SOIC 8-pin SOIC Temperature -40 to +85 C -40 to +85 C Parts that are ordered with a "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS) result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. IDTTM / ICSTM LOW SKEW 1 TO 4 CLOCK BUFFER 6 ICS524 REV A 101705 ICS524 LOW SKEW 1 TO 4 CLOCK BUFFER FAN OUT BUFFER Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales 800-345-7015 408-284-8200 Fax: 408-284-2775 For Tech Support Corporate Headquarters Integrated Device Technology, Inc. 6024 Silver Creek Valley Road San Jose, CA 95138 United States 800 345 7015 +408 284 8200 (outside U.S.) Asia Pacific and Japan Integrated Device Technology Singapore (1997) Pte. Ltd. Reg. No. 199707558G 435 Orchard Road #20-03 Wisma Atria Singapore 238877 +65 6 887 5505 Europe IDT Europe, Limited Prime House Barnett Wood Lane Leatherhead, Surrey United Kingdom KT22 7DE +44 1372 363 339 (c) 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA |
Price & Availability of ICS524 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |